Ashly FR-8 Owner's Manual Page 20
- Page / 61
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Operating Manual - nX, nXe, and nXp Power Ampliers
20
Copyright© 2013 - Ashly Audio Inc.
3) Use an Ashly WR-5 or neWR-5 remote control.
4) Use the event scheduler.
Note: A full preset recall event will overwrite any unsaved changes, so be sure the current configuration is saved before
continuing or any changes will be lost. The amplifier always loads the last working settings on power-up, to preserve any changes
should the power be inadvertently turned off prior to saving a preset. Caution: A new preset may have dramatically different
settings capable of damaging sound system components, so be careful not to recall the wrong preset while the system is on.
9.4 Device Control Tabs
The following device control tabs are available for each amplifier. The tabs include Control Surface, Security, Network
Properties, DSP, Input Source, Meters, Meter Dynamics, Meters AutoLeveler, Metering, Event Scheduler, and Fault Log.
9.4a Software Control Surface - Global
The control surface is the main user interface for the
amplifier section. DSP functions, if available, are managed from
the DSP tab. The following amplifier functions are available in
the control panel:
Name - The user defined name for this specific
amplifier. Up to 20 characters can be used.
Model - The model of amplifier being addressed
Power - Shows power status as On, Off, or Standby.
Power On/Standby - This
shows power status and allows the user to set power to standby from software. Standby can
also be controlled by a rear panel contact closure or by the event scheduler.
The front panel power switch blinks when in standby.
Front Panel Enable/Disable - This disables both the front panel power switch and all level controls, fixing the value of
all level controls at maximum (fully on) regardless of their position.
Note that the software attenuators shown on the control surface
will always reflect the physical position of the amplifier's front panel attenuators, even when they are disabled and not attenuating the signal.
Remote Attenuator Enable/Disable - Disables all "Remote DC Level Control" Euroblock connectors on back panel
Protect - Channel Thermal - This tracks the front panel TEMP LED, lit when amp temperature is 80% of maximum
allowed. At 90% of maximum, attenuation is applied to the overheating channel. (see section 3 or section 14)
Protect - Channel Average Power - This shows that the amplifier has automatically attenuated signal to prevent an
over-power output condition. (see section 3 or section 14)
Protect - Channel Rail Fault - This means there is an overvoltage or
undervoltage condition on the output DC power supply voltage rails. They are
outside of their specified tolerance range. (see section 3 or section 14)
Internal Amplifier Ambient - This indicates the internal temperature.
DIP Switch Settings - Each channel has a six position rear-panel DIP switch
for setting HPF, Limiter, Gain, and Output Mode. All current DIP switch positions
and parameters are displayed here on the software control surface.
9.4a - Control Surface Global Functions
9.4a - DIP Switch Settings
- Power Amplifiers 1
- Important Safety Instructions 2
- FCC Compliance 3
- Table of Contents 4
- 1 INTRODUCTION 6
- Total Power Draw 7
- 2.2 Input Signal Wiring 8
- 2.3 Output Speaker Wiring 8
- 2.4 Remote Control Wiring 8
- 2.6 Mechanical 9
- 2.7 Cooling 9
- 3 nX AMPLIFIER PROTECTION 10
- 4.4 Channel Attenuators – 11
- 4.5 Channel LED Indicators 11
- 4.6 Amplifier Status LEDs 11
- 4.7 Power Switch/LED – 11
- 1 2 5 6 83 4 7 12
- 2 3 4 5 6 7 8 13
- (nXe and nXp models only) 14
- 9 PROTEA 15
- SOFTWARE 15
- 9.1c File Menu 16
- 9.1d Network Menu 16
- 9.1e Project Menu 16
- 9.1f Add Item Menu 16
- 9.1g Options Menu 17
- 9.1h Flash Programmer Menu 17
- All Rights Reserved 19
- 9.4 Device Control Tabs 20
- 9.4b Security Tab 22
- 9.4d DSP Control Tab 23
- 1) Dynamics Controls 24
- Autoleveler 25
- Noise Gate 27
- Gain Functions 29
- Gain with VCA 30
- RD-8C Remote Control Gain 30
- Equalization 31
- *.fir file example: 35
- *.csv file example: 35
- 4) Crossover Functions 36
- HPF and LPF filters 37
- 5) Delay 38
- 6) Metering 38
- 7) Signal Generator 38
- Matrix Mixer and Auto Mixer 39
- Matrix Mixer 39
- Auto Mixer 40
- 9.4e Input Source Tab 41
- 9.4g Events Tab 41
- Function Control Device(s) 42
- 10.4 Sleep Clock Timer 43
- 10.5 Preset Recall 43
- 10.6 Gain Control 43
- 10.7 Channel Mute 44
- 13 NETWORK AUDIO OPTIONS 49
- 13.1a CobraNet 50
- Configuration Tab 50
- 13.2 Dante 51
- Network Audio 51
- (0dBu = 0.775V rms) 54
- Input Source Selection 56
- Dynamics 56
- OBTAINING WARRANTY SERVICE: 58
Related products and manuals for Audio equalizers Ashly FR-8
Audio equalizers Ashly 4.24D User Manual
(8 pages)
(8 pages)
(12 pages)
Audio equalizers Ashly 2.24PS Specifications
(20 pages)
(20 pages)
Audio equalizers Ashly 4.24D Specifications
(20 pages)
(20 pages)
Audio equalizers Ashly 4.24G User Manual
(16 pages)
(16 pages)
© 2020, manymanuals.com. All rights reserved. | 0.308 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals